Гидравлическое давление при валковом отжиме

Sh.R. Khurramov; A.A. Saliyev

doi:10.47813/2782-2818-2023-3-1-0301-0310

Authors

Sh.R. Khurramov Tashkent University of Architecture and Civil Engineering, Tashkent, Republic of Uzbekistan
A.A. Saliyev Tashkent State University of Economics, Tashkent, Uzbekistan

DOI:

https://doi.org/10.47813/2782-2818-2023-3-1-0301-0310

Keywords:

roller squeezing, moisture filtration, hydraulic pressure, squeezing area

Abstract

The results of the study of hydraulic pressure in the roll squeezing of wet materials are given. Mathematical models of hydraulic pressure distribution in the squeezing zone are developed. It is revealed that the hydraulic pressure in the compression zone increases from zero at the initial contact point to a maximum at a point lying on the line of centers. The distribution patterns of hydraulic pressure in the strain restoration zone depend on the length of its part, where the fluid flows from the wet material into the roll coating.

Author Biographies

Sh.R. Khurramov, Tashkent University of Architecture and Civil Engineering, Tashkent, Republic of Uzbekistan

Shavkat Rakhmatullaevich Khurramov, Doctor of Technical Sciences, Professor, Tashkent University of Architecture and Civil Engineering, Tashkent, Republic of Uzbekistan.

A.A. Saliyev, Tashkent State University of Economics, Tashkent, Uzbekistan

Abdumajit Abdikadirovich Saliyev, Ph.D., Assistant Professor Tashkent State Universty of Economics, Tashkent, Republic of Uzbekistan

References

Хуррамов Ш.Р. Аналитическое описание формы кривых контакта валков в двухвалковом модуле. Известия вузов. Технология текстильной промышленности. 2021; 4(394): 153-158. DOI: https://doi.org/10.47367/0021-3497_2021_4_153

Alexa V., Ratiu S.A., Kiss I, Ciota G. Modelling pressure rolling of asymmetric rolling Process. IOP Conf. Series: Materials Science and Engineering. 2017; 200: 012038.

Tan X. Friction of plasticity: application of the dynamic friction model. J. Engineering Tribology. 2007; 221.

Курбанова Ф.З. Исследование контактного взаимодействия в валковых парах для совершенствования процессов механической обработки листовых материалов: Дис… канд. техн. наук. – Ташкент. 2022; 133.

Новиков Н.Е. Прессование бумажного полотна. М.: Лесная промышленность; 1992. 326.

Паршуков В.Е., Маринин А.Н., Константинова Е.Р., Петрова И.В., Фомин Ю.Г. Влияние технологических факторов на степень отжима влаги из ткани. Известия ВУЗов. Технология текстильной промышленности. 2021; 4(333): 124-127.

Коновалов А.Б. Имитационные моделирование рабочего процесса в прессах продольной фильтрацией. Технико-технологические проблемы сервиса. 2012; 2: 40-47.

Khurramov Sh.R. Filtration rates in roller pressing of fibrous materials. J AIP Conference Proceedings. 2021; 2402: 0300420.

Кузнецов В.А., Петров Н.А., Кортовенко В.М. Физическая модель процесса отжима ткани. Известия вузов. Технология текстильной промышленности. 1987; 2: 90-93.

Iliev O., Printsypar G., Rief S. On mathematical modeling and simulation of the pressing section of a paper machine including dynamic capillary effects: One-dimensional model. J Transport in Porous Media. 2012; 92: 41-59.

Bezanovic D., Duin C. J., Kaasschieter E.F. Analysis of wet pressing of paper: The three-phase model, Part II. Compressible air case Transport in Porous Media. 2007; 67: 171-187.

Khurramov, Sh., Kurbanova, F. Hydraulic Problems of the Theory of Roller Pressing Hides. AIP Conference Proceedings. 2022; 2637: 060004.

REFERENCES

Hurramov SH.R. Analiticheskoe opisanie formy krivyh kontakta valkov v dvuhvalkovom module. Izvestiya vuzov. Tekhnologiya tekstil'noj promyshlennosti. 2021; 4(394): 153-158.

Alexa V., Ratiu S.A., Kiss I, Ciota G. Modelling pressure rolling of asymmetric rolling Process. IOP Conf. Series: Materials Science and Engineering. 2017; 200: 012038. DOI: https://doi.org/10.1088/1757-899X/200/1/012038

Tan X. Friction of plasticity: application of the dynamic friction model. J. Engineering Tribology. 2007; 221. DOI: https://doi.org/10.1243/13506501JET193

Kurbanova F.Z. Issledovanie kontaktnogo vzaimodejstviya v valkovyh parah dlya sovershenstvovaniya processov mekhanicheskoj obrabotki listovyh materialov: Dis… kand. tekhn. nauk. – Tashkent 2022. 133.

Novikov N.E. Pressovanie bumazhnogo polotna. M.: Lesnaya promyshlennost’; 1992. 326.

Parshukov V.E., Marinin A.N., Konstantinova E.R., Petrova I.V., Fomin YU.G. Vliyanie tekhnologicheskih faktorov na stepen' otzhima vlagi iz tkani. Izvestiya VUZov. Tekhnologiya tekstil'noj promyshlennosti. 2021; 4(333): 124-127.

Konovalov A.B. Imitacionnye modelirovanie rabochego processa v pressah prodol'noj fil'traciej. Tekhniko-tekhnologicheskie problemy servisa. 2012; 2: 40-47.

Khurramov Sh.R. Filtration rates in roller pressing of fibrous materials. J AIP Conference Proceedings. 2021; 2402: 0300420. DOI: https://doi.org/10.1063/5.0071266

Kuznecov V.A., Petrov N.A., Kortovenko V.M. Fizicheskaya model' processa otzhima tkani. Izvestiya vuzov. Tekhnologiya tekstil'noj promyshlennosti. 1987; 2: 90-93.

Iliev O., Printsypar G., Rief S. On mathematical modeling and simulation of the pressing section of a paper machine including dynamic capillary effects: One-dimensional model. J Transport in Porous Media. 2012; 92: 41-59. DOI: https://doi.org/10.1007/s11242-011-9890-y

Bezanovic D., Duin C. J., Kaasschieter E.F. Analysis of wet pressing of paper: The three-phase model, Part II. Compressible air case Transport in Porous Media. 2007; 67: 171-187. DOI: https://doi.org/10.1007/s11242-006-0018-8

Khurramov, Sh., Kurbanova, F. Hydraulic Problems of the Theory of Roller Pressing Hides. AIP Conference Proceedings. 2022; 2637: 060004. DOI: https://doi.org/10.1063/5.0118674